CETUS xl Advanced Patient Monitor

Ապրանքի կոդ
Գին

aXcent CETUS xl Advanced Patient Monitor

Բազմաթիվ պարամետրերի ընտրանին բավարարում է  բոլոր պահանջները ICU, CCU, NICU-ի համար։

Կոնֆիգուրացիա՝   ECG, SpO2, NIBP, Resp, PR; Li-ion մարտկոց

Ընտրովի՝ 12-կանալային ԷՍԳ, Masimo SpO2, 2/4/6 IBP, C.O.,EtCO2, Multi-gas, BIS, NMT; VGA, Ջերմային Ձայանգրիչ ,լարով/անլար CMS

  • 15.6”/17/19” switchable TFT LCD սենսորային մոնիտոր
    • Ալյումինե պարկուճ
    • Առանց օդափոխման դիզայնով, միանգամայն հարմարավետ է միջավայրի համար
    • 10 ալիքաձև կորերի ցուցադրումից մինչև 12-կանալային ԷՍԳ վերլուծություն
    • Օգտակար հաշվարկ (Hemodynamic, Drug Dose, Oxygenation, Ventilation)
    • SpO2 support PVI and PI, low perfusion 0.2%
    • Aspect BISx մոդուլ, NMT ընտրովի մոդուլ
    • Լարային/անլար CMS, support HL7 protocol to HIS
    • SpO2 զարկերակային տոնի փոփոխում (Pitch Tone)
    • VGA support external display
    • Գրաֆիկական և աղյուսակային զննման հնարավորություն (120 ժամ)
    • 48 ժամյա ամբողջական ալիքային զննում յուրաքանչյուր հիվանդի համար

Technical Specifications

Display
15.6” TFT Touch screen
Resolution: 1366 x 768
Number of traces: 10 waveforms
I/O
LAN: 1 standard RJ45 port
WLAN: IEEE 802.11b/g/n
USB: 2 USB connectors
SD: 1 SD card socket
VGA: 1 VGA monitor connector
Output: 1 connector for Nurse call,
Defib Sync Analog Output
ECG
Lead type: 3-lead, 5-lead,12-lead
ECG waveform: 2 channels, 7 channels,
12 channels
Display sensitivity: 2.5 mm/mV (×0.25),
5 mm/mV (×0.5), 10 mm/mV (×1.0),
20 mm/mV (×2.0)
Wave sweep speed: 6.25mm/s, 12.5 mm/s,
25 mm/s, 50 mm/s
Bandwidth
Diagnostic mode: 0.05 Hz~100 Hz
Monitor mode: 0.5 Hz~40 Hz
Surgery mode: 1 Hz~20 Hz
Strong filter mode: 5Hz~20 Hz
CMRR>100dB
Notch: 50/60Hz notch filter can be set to
on or off
Differential input impedance >5 MΩ
Electrode polarization voltage range: ±400 mV
Baseline recovery time <3s after defibrillation
(in monitor and surgery mode)
Calibration signal: 1 mV (peak – peak),
accuracy ±3%
RESP
Measurement method: Thoracic electrical
bioimpedance
Rate: 0 – 150 bpm
Measuring lead: Lead I, II
Wave gain: ×0.25, ×0.5, ×1, ×2
Respiratory impedance range: 0.5-5 Ω
Baseline impedance: 500-4000 Ω
Gain: 10 grades
Scan speed: 6.25 mm/s, 12.5 mm/s, 25 mm/s
TEMP
Accuracy: ±0.1 °C or ±0.2 °F (without probe)
Measurement range: 5~50 °C (41~122 °F)
Channel: Two channels
Resolution: 0.1 °C
Parameters: T1, T2 and TD
SpO2
Measurement range: 0-100%
Resolution: 1%
Accuracy: ±2% (70-100%, Adult/Pediatric);
±3% (70-100%, Neonate);
0-69%, unspecified
Refreshing Rate: 1s
Masimo SET® SpO2(Optional)
Measurement range: 0-100%
Resolution: 1%
Accuracy: ±2% (70-100%, Adult/Pediatric,
non-motion, low prefusion);
±3% (70-100%, Neonate,
non-motion);
±3% (70-100%, motion);
0-69%, unspecified
Refreshing Rate: 1s
Pulse Rate
Range: 30~254 bpm
Resolution: 1bpm
Accuracy: ±2bpm (non-motion)
±5bpm (motion)
Refreshing rate: 1s
NIBP
Measurement method: Automatic
oscillometric method
Operating mode: Manual, automatic,
continuous
Measurement unit: mmHg/kPa selectable
Typical measurement time: 20~40s
Measurement type: Systolic, Diastolic, Mean
Measurement range (mmHg)
Range of Systolic pressure: Adult 40-270
Pediatric 40-200
Neonatal 40-135
Range of Diastolic pressure: Adult 10-210
Pediatric 10-150
Neonatal 10-95
Range of Mean pressure: Adult 20-230
Pediatric 20-165
Neonatal 20-105
Measurement accuracy
Maximum average error: ±5 mmHg
Maximum standard deviation: 8 mmHg
Resolution: 1 mmHg
Interval: 1, 2, 3, 4, 5, 10, 15, 30, 60, 90, 120, 180,
240, 480 minutes
Overpressure protection: Software and
hardware, double safety protection
Cuff pressure range: 0-280mmHg
IBP (Optional)
Channel: 2, 4 or 6-channel
ART: 0 to 300 mmHg
PA: -6 to 120 mmHg
CVP/RAP/LAP/ICP: -10 to 40 mmHg
Measurement range: P1/P2 -50 to 300 mmHg
Resolution: 1 mmHg
Accuracy: ±2% or ±1 mmHg,
whichever is greater (without sensor)
Sensitivity: 5uV/mmHg/V
Impedance range: 300 to 3000 Ω
C.O. (Optional)
Method: Thermodilution
Range: C.O.: 0.2 to 20 L/min
TB: 23 to 45 °C
T1: -1 to 27 °C
Accuracy: C.O.: ±5% or ±0.1L/min,
whichever is greater TB, T1: ±0.5°C
(without sensor)

 

Standard Mainstream CO2 (Optional)
Measurement range: 0-19.7%,
150 mmHg, or 0-20kPa
Resolution: 0.1 mmHg
Measurement accuracy
0 – 40 mmHg: ± 2 mmHg
41 – 70 mmHg: ± 5% of reading
71 – 100 mmHg: ± 8% of reading
101 – 150 mmHg: ± 10% of reading
Respiration rate: 3-150 bpm
Respiration rate accuracy: 1% ±1 bpm
Warm-up time: 97% within 8s, full accuracy
within 20s
Standard Sidestream CO2 (Optional)
Measurement rage: 0-20% (0-150 mmHg)
Accuracy: < 5.0% CO 2: ± 2 mmHg
> 5.0% CO 2: < 6% of reading
Respiration rate: 2~150 BPM
Respiration rate accuracy: 1% ±1BPM
Warm-up time: 97% within 45s, full accuracy
within 10 min
Rise times (t10-90%): About 100 ms, when
flow is 100 ml/min, adult water trap 1.5m
sampling tube
Delay time: <3sec when flow is 100 ml/min,
adult water trap 1.5 m sampling tube
Recorder (Optional)
Built-in, Thermal dot array
Horizontal resolution: 16 dots/mm (25 mm/s
paper speed)
Vertical resolution: 8 dots/mm
Paper speed: 25 mm/s, 50 mm/s
Number of waveform channels: 3
Phasein ISA Sidestream CO2 (Optional)
Warm-up time: Full accuracy within 10 seconds
Sampling flow rate: 50ml/min(+/-10/min)
Measurement Range: 0 -25%
Accuracy: 0~15% (±0.2% of the reading)
15~25%, unspecified
Rise time: 200 ms, typical at 50 ml/min
flow rate
Total response time: within 3 seconds
(with 2 m Nomoline sampling line)
AWRR Range: 0-150 bpm
AWRR Accuracy: ±1 breath
Phasein IRMA™ Mainstream CO2 (Optional)
Measurement Range: 0 -25%
Accuracy: 0~15% (±0.2% of the reading)
15~25%, unspecified
Warm-up time: Full accuracy within
10 seconds
AWRR Range: 0-150 bpm
AWRR Accuracy: ±1 breath
Phasein IRMA™ AX+ Mainstream Multi-gas
(Optional)
Gas: CO2, N2O, HAL, ISO, ENF, SEV, DES with
automatic identification
Warm-up time: Full accuracy within
20 seconds for IRMA AX+
CO2 Accuracy:
0-10%: ± (0.2%+2% of the reading)
0-15%: ± (0.3%+2% of the reading)
N2O Accuracy:
0-100%: ± (2%+2% of the reading)
HAL, ISO, ENF:
0-8%: ± (0.15%+5% of the reading)

SEV:0-10%: ± (0.15%+5% of the reading)
DES:0-22%: ± (0.15%+5% of the reading)
Agent identification time: <20s(typical <10s)
AWRR range: 0-150 bpm
AWRR accuracy: +/-1 bpm
Apnea time: 20~60s
Aspect BISx module (Optional)
Parameter Measurement:
BC: 0~30 (Only limited to the combined use of
an external sensor with a BIS module)
EMG: 30~55dB (bar chart) with intensity
between 30dB and 80dB (tendency chart)
BIS: 0~100
SQI: 0%~100%
SR: 0%~100%
SEF: 0.5 Hz~30Hz
TP:40~100 Db
EEG Measurement: Input impedance >5 MΩ
Noise (RTI) <2μV (0.25~50 Hz)
Input signal range: ±1 Mv
EEG bandwidth between: 0.25 Hz~110 Hz
NMT Tof-Watch® SX (Optional)
Microprocessor-controlled
Stimulation Mode: TOF, TOFS, PTC, 1Hz
Twitch, 0.1Hz
Twitch, DBS DBS3.3 and 3.2 (Double Burst),
Tetanic Stimulation (Burst), 5s – 50 Hz or
100 Hz
Output (accuracy ±5% of full scale value)
Surface electrodes:
Constant current,0-60mA(0-12/18μC) up to
5 KOhm.
Monophasic, 200 μs or 300 μs pulse width
Needle electrodes:
Constant current, 0-6 mA (0-0.24 μC) up to
5 KOhm.
Monophasic, 40μs pulse width
Acceleration transducer: Accuracy ±5% of full
scale value
Temperature sensor: Range 20.0-41.5 °C
(accuracy ±5 °C)
Operation Environment
Power: AC 100-250 V, 50/60 Hz
Temperature: 5-40 °C
Humidity: <80%
Patient Range: Adult, Pediatric, Neonate
Battery backup: Standard 2-3 hrs (2.600 mAh),
optional 3-5 hrs (4.800 mAh)